Skip to content

How To Remove Bath Drain Plug

There are a few ways to remove a bath drain plug. The most common is to use a plunger. If the plunger doesn’t work, you can try using a wire hanger. If that doesn’t work, you can try using a screwdriver.

How To Remove Bath Drain Plug

Removing a bath drain plug can be a bit tricky if you’re not familiar with how it’s done. There are a few ways to do it, but the most common way is to use a plumber’s wrench. If you don’t have a plumber’s wrench, you can use a regular wrench, or even a pair of pliers. The key is to get a good grip on the plug and twist it counter-clockwise until it comes loose.

-A screwdriver -A plumber’s wrench or a basin wrench -channel locks -a bucket

  • Replace the drain plug and screw it back on
  • Clean out any gunk or hair that may be blocking the drain with a plunger
  • Using a wrench, unscrew the drain plug from the bathtub drain

-Remove the drain plug by turning it counterclockwise. -If the plug is stuck, use a plumber’s helper to loosen it. -Be careful not to lose the washer that goes on top of the plug.


Frequently Asked Questions

How Do You Get A Twist Drain Plug Out?

The easiest way to remove a twist drain plug is to use a pipe wrench. If the plug is corroded, you can use a hacksaw to cut the plug off.

How Do You Remove A Twist Bath Overflow Cover?

To remove a twist bath overflow cover, one would need to twist it counter-clockwise and then pull it off.

What Do You Do When Your Bathtub Drain Won’T Unscrew?

I would try to use a plunger on the drain to dislodge any clogs. If that doesn’t work, I would try using a screwdriver to unscrew the drain. If neither of those methods works, I would call a plumber.

How Do You Remove A Bathtub Drain Cover Without Screws?

To remove a bathtub drain cover without screws, one can use a flathead screwdriver to pry the drain cover off.

How Do You Remove A Twist Top Shower Drain?

To remove a twist top shower drain, one needs to remove the top of the drain and unscrew the screw that is holding the screen in place.

How Do You Remove A Bathtub Drain That Won’T Unscrew?

There are a few possible methods for removing a bathtub drain that won’t unscrew. One is to try to use a wrench to loosen the drain. If that doesn’t work, then a hacksaw may be needed to cut through the metal drain. Finally, a drill with a metal-cutting bit could be used to cut through the screw.

How Do You Unscrew A Drain Plug?

The first step to unscrewing a drain plug is locating the plug. It is usually a small, cylindrical object with a screw thread at the top. Once you have found the plug, use a wrench to loosen it by turning it counter-clockwise. Be careful not to over-tighten the plug or you may damage it.

How Do You Remove A Flip Top Drain Stopper?

To remove a flip top drain stopper, you need to unscrew the retaining ring that holds it in place. After removing the ring, the stopper can be pulled out.

How Do You Remove A Lift And Turn Drain Stopper With A Set Screw?

The lift and turn drain stopper with a set screw can be removed by using a screwdriver to loosen the set screw and then pulling the stopper out of the drain.

How Do You Open A Twist Shower Drain?

There is usually a small lever or knob on the top of the twist shower drain that you can use to open it.

How Do You Remove A Twist Style Drain Plug?

To remove a twist style drain plug, one would need either a pipe wrench or a crescent wrench. The pipe wrench would be used if the plug is corroded in place, and the crescent wrench would be used if the plug has a hexagonal head.

How Do You Remove A Twist Drain Plug?

If the twist drain plug is difficult to remove, one can try to use a plumber’s wrench. If that does not work, one can try using a hammer and chisel to break the plug loose.


To Summarize

The best way to remove a bath drain plug is to use a plunger. Put the plunger over the drain and push and pull the plunger up and down.

Leave a Reply

Your email address will not be published.