Skip to content

How To Install Canned Lights In Existing Ceiling

Installing canned lights in an existing ceiling is a fairly easy process. The first step is to remove the old light fixture, if there is one. Next, measure the hole where the light will go and cut a piece of drywall to fit. Then, use a drill to make a hole in the center of the drywall for the electrical box. Feed the wires through the hole and into the electrical box. Attach the drywall to the ceiling with screws and then install the light

How To Install Canned Lights In Existing Ceiling

If you are looking to install canned lights in an existing ceiling, the first thing you will need to do is identify the location of the joists in the ceiling. Once you have located the joists, you can use a stud finder to identify the location of the wall studs. Once you have identified the location of the joists and wall studs, you can mark the locations on the ceiling with a pencil. Next, you will need to cut a hole in the

-Canned lights -Tape measure -Stud finder -Drill -1/2″ drill bit -Paint brush or roller -Ladder -Paint -Ceiling light fixture

  • If your ceilings are not textured, use painter’s tape to mark out the area where the light will be installed
  • If your ceilings are textured, use a can of texture spray to cover the light
  • Cut a hole

-Check the size of the opening in the ceiling – you will need a can light that is the same size or smaller -Determine if you want to install a new electrical box in the ceiling – this is necessary if there is not already an electrical box in the desired location -If you are installing a new electrical box, use a stud finder to determine where the joists are in the ceiling and mark their location on the ceiling with a pencil –


Frequently Asked Questions

Can I Add Recessed Lights To Existing Circuit?

Yes, you can add recessed lights to an existing circuit as long as you have enough wattage capacity on the circuit. If the circuit is already at its max wattage capacity, you will need to add a new circuit specifically for the recessed lights.

Can Recessed Lights Be Added?

Yes, recessed lights can be added. However, consult with an electrician to make sure that the wiring is sufficient to support the additional lights.

How Do I Add An Additional Recessed Light?

To add an additional recessed light, you will need to identify the wiring in your ceiling and run a new wire from the light to the power source. You may also need to install a new switch if there is not already one in the area where you would like to install the light.

Can You Add Recessed Lighting To Existing Ceiling?

Adding recessed lighting to an existing ceiling is a relatively easy task, and can be completed in as little as a few hours. First, measure the area where the new light will be installed and purchase the correct-sized recessed lighting housing and trim kit. Next, use a stud finder to locate the joists in the ceiling and mark their location with a pencil. Then use a drill to create a hole in the ceiling at each mark, making sure to use a bit that’s the same size as the recessed housing. Finally, fit the housing into the holes, secure it with screws, and attach the trim kit.

How Many Recessed Lights Can Be On A Circuit?

A single 15-amp circuit can support up to 12 recessed lights.

Can I Daisy Chain Led Recessed Lights?

Yes, you can daisy chain LED recessed lights by connecting the wires on the back of the lights. Make sure to match the polarity of the connections (i.e. positive to positive, negative to negative) to avoid damaging the lights.

How Do You Install Led Recessed Lights In An Existing Light Fixture?

There is no one-size-fits-all answer to this question, as the procedure for installing LED recessed lights in an existing light fixture may vary depending on the specific light fixture in question. However, in general, the installation process will likely involve removing the existing light bulb and/or socket from the fixture, inserting the LED recessed light into the socket, and then replacing the light bulb and/or socket.


To Summarize

In order to install canned lights in an existing ceiling, one must first measure the dimensions of the desired space and purchase a light fixture that is appropriately sized. The next step is to cut a hole in the ceiling using a drill or jigsaw, and then insert the light fixture into the hole. Finally, attach the light fixture to the ceiling by using screws or nails.

Leave a Reply

Your email address will not be published.